Yamato-scientific IM400W Shaking incubator User Manual

Instruction ManualforIncubator Shaker modelIK 400IK 400WIM 400IM 400W2nd Editionz Thank you for purchasing the Yamato Scientific IK/IMincubator shak

8Before UseInstallation and Preparation Before UseWARNINGObserve the Power Rating.Use a power outlet whose rating meets the electric capacity.Electric

9Before UseInstallation and Preparation Before UseWARNINGMake fine adjustments for precise level installation.After determining where to install the p

10Before UseInstallation and Preparation Before UseCAUTIONHandle the Power Cord Carefully.z Do not entangle the power cord. This will cause overhea

11Handling PrecautionsInstallation and Preparation Before UseWARNINGDo Not Use Flammable or Explosive Gases or Vapors.Do NOT use flammable or explosiv

12Handling PrecautionsCAUTIONDefrostingDuring operation at low temperatures, the evaporator becomes heavily frosted. This large amount offrost degr

13Handling PrecautionsCAUTIONDo Not Use Corrosive Samples.z A major part of the internal structure is stainless steel (JIS SUS304 – JIS stands for Jap

14OperationPlacing Flasks Placing Flasks① Open the door and confirm that shaking has stopped.② Swing the handle out and turn it clockwise 90 degree

15OperationPlacing Flasks⑥ Attach the clamp ring in its correct position as shown in the figure below.⑦ Attach rings to all the clamps including thos

16OperationPlacing FlasksPlace flasks properly.Place each flask so its center is aligned with the middle of the clamp and so it sits straight up.Do no

17OperationSetting the Temperature① Press the temperature set key (). The indicator then displays the previous temperature setpoint.The temperature s

IndexSymbol Conventions...

18Pressing thekey in this mode does not affect thetemperature setpoint at all.⑧ The occurrence of a problem in temperature control is indicated by an

19OperationOperating the Shaker① For safe operation, keep the “door safety” key () switched on.② Turn the speed control knob to its leftmost position

20OperationDefrosting① Operation at a low temperature for a long period causes the buildup of frost, which degrades the freezingperformance and may di

21Safety Systems and Error CodesThis incubator features safety systems independent of the controller, in addition to the self-diagnosticsfunction of t

22MaintenanceDaily Maintenance and InspectionWARNINGDo NOT Make Modifications to This Product.Disassembly of the product is strictly prohibited. Th

23MaintenanceDaily Maintenance and Inspection Cleaning the Condenser SlatsDust adhering to the condenser slats degrades freezing ability and may prev

24MaintenanceDaily Maintenance and Inspection Adjustment of Tension of V BeltVarious problems may result from improper tension of the V belt. To a

25MaintenanceDaily Maintenance and Inspection Inspection and Maintenance of Drawer HandleIf the shaking table plays back and forth even when the tabl

26MaintenanceDaily Maintenance and Inspection Inspection of Slide RailsThe working surfaces of the steel ball bearings, which are used for the slide

27MaintenanceIf Not Using the Product for a Long Period or If Disposing of ItWARNINGIf Not Using for a Long PeriodIf you will not be using the product

1Symbol Conventions Safety SymbolsThe following safety symbols are used on the product and in this manual. Be sure to follow the instructions andr

28After-Sales Service and GuaranteeRequests for Repairs Requests for Repairs Guarantee (given with product)z A certificate of guarantee is given by

29After-Sales Service and GuaranteeTroubleshootingProblem Causes Countermeasures(1) Unusual noise is heard duringshaking1. The tray is not sitting o

30Wiring DiagramNote: Common to all modelsSymbol Part Symbol PartC Condenser P-IN-CONT Temperature control boardELB Earth leakage breaker POWER Motor

31SpecificationsModel IK400 IK400W IM400 IM400WTemperature control method Draft circulationShaking method Horizontal back-and-forth Horizontal rotatin

32Replacement Parts Parts Common to the IK and IM SeriesPart Code Number.Specification ManufacturerTemperature controlboard1-01-180-0003 P-IN-CONT (f

33 Parts Common to IK SeriesPart Code Number.Specification ManufacturerBearings for linkage shaft 4-18-003-0001 UFL000 KOYO, JapanSupport roller4-18-

34ReferenceDangerous Substances① Ethylene glycol dinitrate (nitroglycol), glycerine trinitrate (nitroglycerine),cellulose nitrate (nitrocellulose), an

2Safety PrecautionsWARNING1. Do NOT Use Where Flammable or Explosive Gases or Vapors Are Present.Do NOT operate this product where there are flammable

3Before UseParts and Their Functions: ExteriorNote: Models IK400W and IM400W are furnished with a glass door.Front ViewRear ViewInside DoorHingeDoorTe

4Before UseParts and Their Functions: Structural DrawingsIK SeriesUnit: mmFlaskFlask clampLink rodCrankShaker motorV beltBearingV pulleyPhoto slit for

5Before UseParts and Their Functions: Structural DrawingsIM SeriesUnit: mmFlaskFlask clampCrankShaker motorV beltBearingV pulleyPhoto slit forrotation

6Before UseParts and Their Functions: Operation Panel① Speed indicatorDisplays the shaking speed in tenths of the revolutions per minute.② Speed contr

7Before UseInstallation and Preparation Before UseWARNINGDo NOT Use Where Flammable or Explosive Gases or Vapors Are Present.Do NOT operate this produ