Constant Temperature Drying Oven Model DVS402 DVS602 First edition ● Thank you very much for purchasing this Yamato DVS series constant temp
8 2. Before operating the unit Precautions when installing the unit Caution 11. About handling of the power cord Never use electrical power c
9 3. Names and functions of parts Main body Front view Rear panel Control panel Door Handle Main switch (Earth leakage breaker) Ra
10 3. Names and functions of parts Operation panel MEASURED TEMP. ℃HEATERALARMAUTO STOPAUTO STARTENTER SETTEMP.OVER TEMP.PROTECTORFIXED TEMP.RUN S
11 3. Names and functions of parts Explanation of characters Characters on the VS4 type controller are explained in this section. Characters Ident
12 3. Names and functions of parts Explanation of characters Characters Identifier Name Application cAL Calibration offset settingUsed for inp
13 4. Operating procedures List of operation modes and functions Operation modes of the unit are as shown below: № Name Description Page1 Fixed tem
14 4. Operating procedures List of operation modes and functions Operating functions of the unit are as shown below: № Name Description Page1 Overh
15 4. Operating procedures Operation mode・function setting keys and characters Key operations and characters in the diagram below are used for operat
16 4. Operating procedures Settings for overheat prevention device The safety device for preventing overheat has the automatic overheat prevention fu
17 4. Operating procedures Operating procedures (fixed temperature operation) How to start fixed temperature operation MEASURED TEMP. ℃HEATERALARM
Table of contents 1. Safety precautions ...
18 4. Operating procedures Operating procedures (quick auto stop operation) Procedures for quick auto stop operation Used when you want to, for examp
19 4. Operating procedures Operating procedures (auto stop operation) Procedures for auto stop operation Used when you want to “set automatic stop af
20 4. Operating procedures Operating procedures (auto stop operation) MEASURED TEMP. ℃ HEATERALARMAUTO STOPAUTO STARTENTER SETTEMP.OVER TEMP.PROTECT
21 4. Operating procedures Operating procedures (auto start operation) Procedures for auto start operation Used when you want to “start operation aut
22 4. Operating procedures Operating procedures (auto start operation) MEASURED TEMP. ℃ HEATERALARMAUTO STOPAUTO STARTENTER SETTEMP.OVER TEMP.PROTEC
23 4. Operating procedures Preparing a program Program operation Used when you want to “operation at an increased or decreased temperature according
24 4. Operating procedures Preparing a program Heating・cooling time of the DVS model Rough heating and cooling times of the DVS model are as follow
25 4. Operating procedures Preparing a program MEASURED TEMP. ℃ HEATERALARMAUTO STOPAUTO STARTENTER SETTEMP.OVER TEMP.PROTECTORFIXED TEMP.RUN STOP S
26 4. Operating procedures Preparing a program MEASURED TEMP. ℃ HEATERALARMAUTO STOPAUTO STARTENTER SETTEMP.OVER TEMP.PROTECTORFIXED TEMP.RUN STOP S
27 4. Operating procedures Preparing a program MEASURED TEMP. ℃ HEATERALARMAUTO STOPAUTO STARTENTER SETTEMP.OVER TEMP.PROTECTORFIXED TEMP.RUN STOP S
1 1. Safety precautions Explanation of pictograms A variety of pictograms are indicated in this operating instruction and on products to assure
28 4. Operating procedures Program repeat operation Using the program repeat function This section explains how to register a program pattern to be r
29 4. Operating procedures Programming sheet Make duplicates as necessary. Registration destination PrG1 PrG2 PrG3 PAt1 PAt2 PAt3 Control No.
30 4. Operating procedures Programming sheet Make duplicates as necessary. Registration destination PrG1 PrG2 PrG3 PAt1 PAt2 PAt3 Control No.
31 4. Operating procedures Useful functions (calibration offset function) Using the calibration offset function Calibration offset function compensat
32 4. Operating procedures Useful function (lock function) Using the lock function MEASURED TEMP. ℃ HEATERALARMAUTO STOPAUTO STARTENTER SETTEMP.OVE
33 5. Cautions on handling Warning 1. About substances that cannot be used for the unit Never use an explosive substance, a flammable substance or
34 5.Cautions on handling Caution 7. About placement of samples Withstand load of the shelf boards included is approx. 15kg. Do not place a sample
35 6. Maintenance procedures Daily inspection/maintenance Warning z Be sure to pull out the power cord for the power supply unless necessary befor
36 7. When the unit is not to be used for a long time or when disposing When the unit is not to be used for a long time or when disposing Caution W
37 8. Troubleshooting Safety device and error codes The unit has the self diagnostic function with a controller and a separate safety device. Table b
2 1. Safety precautions List of symbols Warning General warnings Danger!: High voltage Danger!: High temperatureDanger!: Moving part Danger!:Haz
38 8. Troubleshooting When a malfunction is suspected If any of the symptoms below occurs Symptom Check The unit is not activated even if the power
39 9. After sales service and warranty When requesting a repair When requesting a repair If any trouble occurs, immediately stop operation, turn the
40 10. Specifications Model DVS402 DVS602 Operating temperature range Room temperature +5℃∼260℃(no load at an ambient temperature of 23℃) Temperat
41 11. Wiring diagram DVS402/602 1234TELBAC100VHX3412CTX1SSR2113TB1CN2CN112CONT321TB22+-TH2TH1+-CN8CN1118118PIOCN9CN21181181234CN456...13CN52..
42 12. List of replacement parts Common replacement parts for DVS402/602 Part name Standard Maker Code No. 1 Sensor LCK-M1-2000Y @K single Yamat
43 13. List of dangerous materials Never use an explosive material, a flammable material or a material containing them for this device. ① Nitrogl
44 14. Standard installation manual *Install the product according to the following: (Confirm separately for optional items or special specifications
45 Limited liability Be sure to use the unit strictly following the handling and operating instructions in this operating instruction. Yamato Scientif
3 1. Safety precautions Warning・Cautions Warning Never operate the unit in an atmosphere containing flammable or explosive gas Never operate the
4 2. Before operating the unit Precautions when installing the unit Warning 1. Be sure to connect the ground wire. ・ Power supply for this product
5 2. Before operating the unit Precautions when installing the unit Warning 3. Never operate the unit in an atmosphere containing explosive or flamm
6 2. Before operating the unit Precautions when installing the unit Warning 4. Do not alter the product. 5. Install the unit on a level surface T
7 2. Before operating the unit Precautions when installing the unit Caution 8. Be sure to connect the power plug to the dedicated wall outlet. Use
Comments to this Manuals